| Part Number | Description |
| 199-00-35-145 | DISTANCE BOLT FOR 411-17-12-000 |
| 199-00-37-021 | HANDLE TO ADJUST LABEL HEIGHT |
| 199-00-45-019 | LATCH LOCATED ON REMOVABLE COVERS A |
| 199-00-55-052 | BEARING (PRESSION ROLLR) |
| 199-00-58-031 | BUSHING (GUID. ROLLS TAPE UNWINDER) |
| 199-00-71-018 | TOOTHED FLAT BELT (INKING DEVICE DR |
| 199-00-71-040 | TOOTHED BELT (HRZNTL) |
| 199-00-71-041 | TOOTHED BELT CONVEYOR UNIT |
| 199-00-71-042 | TOOTHED BELT (HEIGHT ADJUSTMENT) |
| 199-00-77-028 | CLUTCH GEARING |
| 199-00-77-038 | SLIDING CLUTCH COATING WIND OFF MOT |
| 199-00-77-044 | SLIDING CLUTCH COATING MAIN MOTOR |
| 199-02-03-067 | DC/DC converter 15V, 4A |
| 199-02-03-068 | DC/DC converter 24V, 8A |
| 199-02-12-374 | CLUTCH S1 24 |
| 199-02-12-377 | PLUG |
| 199-02-15-033 | AUT. CUTOUT FAZL 10A |
| 199-02-15-045 | SAFETY SWITCH FAZG 1A |
| 199-02-15-047 | SAFETY SWITCH FAZG 2A |
| 199-02-15-060 | SAFETY SWITCH FAZG 3A |
| 199-02-20-051 | TERMINAL SWITCH LABELING HEIGHT |
| 199-02-20-229 | APPROXIMATIN INITIATIOR PNP |
| 199-02-20-230 | LIMIT SWITCH |
| 199-02-20-235 | ROLL LEVER |
| 199-02-20-236 | RECTANGULAR ROLL LEVER |
| 199-02-20-237 | CODING SWITCH |
| 199-02-20-238 | CODING SWITCH |
| 199-02-20-241 | PRESS BUTTON (WITHOUT CONTACTS) |
| 199-02-20-242 | EMERGENCY OFF BUTTON (WITHOUT CONTA |
| 199-02-20-243 | FLIP SWITCH |
| 199-02-20-257 | CONTACT BLOCK (LOCKER) (MARKED K-10 |
| 199-02-20-258 | CONTACT BLOCK (OPENER) (MARKED K-01 |
| 199-02-30-053 | POTENTIOMETER |
| 199-02-30-056 | PTC RESISTOR - B770 |
| 199-02-50-011 | RECTIFIER SKD 25/02 |
| 199-02-50-031 | RECTIFIER SKD 50/02 |
| 199-02-70-007 | PRINT LOGIC SUPPLY FOR OSCILLATOR ( |
| 199-02-70-033 | PRINT SERVO AMPLIFIER TRIPLE |
| 199-02-70-039 | PRINT SM TERMINAL STEP MIDEX |
| 199-02-70-040 | PRINT OSCILLATOR (800 steps) |
| 199-02-70-041 | PRESELECTION COUNTER 216 |
| 199-02-70-042 | REGISTERING COUNTER 206 |
| 199-02-70-043 | SPEEDOMETER 524 AC |
| 199-02-70-054 | AC SERVO DRIVER BTS 10-200-0,8P E1 |
| 199-02-70-060 | PRINT LOGIC SUPPLY FOR AC SERVO |
| 199-02-70-061 | AC SERVO DRIVER FOR MAIN MOTOR |
| 199-02-70-062 | GENERATOR LOAD MODUL MAIN MOTOR |
| 199-02-85-001 | 6ES51028MA02SPS CENTRAL COMPONENTRY |
| 199-02-85-010 | SPS DIGITAL INPUT GROUP, 4 INPUTS |
| 199-02-85-011 | 6ES54218MA12 - SPS DIGITAL INPUT GR |
| 199-02-85-020 | SPS DIGITAL OUTPUT GROUP, 4 OUTPUTS |
| 199-02-85-040 | 6ES57008MA11 - RACK TERMINAL (BUS M |
| 199-06-03-044 | PEL TUBE í 3mm, l=1m |
| 199-06-55-003 | DISPOSABLE AIR FILTER |
| 199-06-55-004 | PEL SWITCH |
| 199-08-10-046 | STEPPING MOTOR |
| 199-08-10-112 | BRUSH HOLDER |
| 199-08-10-113 | GRAPHITE BRUSH |
| 199-08-10-117 | GRAPHITE BRUSH MAIN MOTOR |
| 199-08-10-118 | GRAPHITE BRUSH SPEEDING GENERATOR |
| 199-08-10-129 | FILTER PAD |
| 199-08-10-140 | STEPPING MOTOR |
| 199-08-10-159 | EXHAUST FAN WITH BEARINGS |
| 199-08-20-018 | LOCKING MAGNET |
| 199-08-30-089 | SEMICONDUCTOR RELAY 25D |
| 199-08-30-155 | MOTOR SAFETY SWITCH PKZM1-0,4 |
| 199-08-30-158 | MOTOR SAFETY SWITCH PKZM1-1,6 |
| 199-08-30-163 | MOTOR SAFETY SWITCH PKZM1-16 |
| 199-08-30-166 | CONTACTOR DIL OOAM-10 |
| 199-08-30-167 | CONTACTOR DIL OAM |
| 199-08-30-168 | CONTACTOR 11 DILM |
| 199-08-30-181 | OPTO COUPLER EMO1-OV-24DC |
| 199-08-30-182 | OPTO COUPLER EMO1-OV-12DC |
| 199-08-30-215 | ELECTRONIC COUPLER |
| 199-10-32-005 | LUMINOUS DIODE RED |
| 199-10-32-006 | LUMINOUS DIODE YELLOW |
| 199-10-32-007 | LUMINOUS DIODE GREEN |
| 411-17-01-017 | BOLT |
| 411-17-01-025 | SPRING |
| 411-17-04-005 | ROD |
| 411-17-04-011 | CUTTING KNIFE 85 mm |
| 411-17-04-016 | CUTTING KNIFE 120 mm |
| 411-17-06-072 | SM-PRESSION ROLLER COMPLETE FOR 85M |
| 411-17-06-107 | SM-DRIVE ROLLER COMPLETE FOR 85MM C |
| 411-17-06-117 | SUPPORT FOR PRESSION ROLLER |
| 411-17-06-119 | TENSION SPRING (PRESSION ROLLER) |
| 411-17-06-120 | HOLDER FOR ASSEMBLY FOR PRESSION RO |
| 411-17-06-122 | BACKING PLATE FOR ROLLER FOR ADVANC |
| 411-17-06-129 | RING 9MM WIDTH (LOCKING COLLAR ON C |
| 411-17-06-140B | METALIZED DRIVE ROLLER |
| 411-17-06-203 | AXLE |
| 411-17-06-207 | SM-DRIVE ROLLER COMPLETE FOR 120MM |
| 411-17-06-218 | AXLE FOR PRESSION ROLLER ASSEMBLY F |
| 411-17-07-043 | STAPLE SHEET (REMOVABLE PLATE AT TO |
| 411-17-11-002 | GRAPHITE TUBE FOR VACUUM PLATE VENT |
| 411-17-11-010 | DRUM KNIFE 85 mm-(SEE NOTES) |
| 411-17-11-013 | SENSOR PT100 |
| 411-17-11-014 | HEATING CARTRIDGE 85 mm |
| 411-17-11-015 | FLANGE PACKING |
| 411-17-11-033 | DRUM KNIFE 120 mm |
| 411-17-11-034 | HEATING CARTRIDGE 120 mm |
| 411-17-12-000 | PRINT LABELING HEAT CONTROLLER |
| 411-21-02-004 | SHAFT |
| 411-21-02-050 | SYNTHETIC TOOTHED WHEEL (INKING DEV |
| 411-21-02-076 | TENSION SPRING (STAMP) |
| 411-21-02-087 | SHIFT GEAR |
| 411-21-02-114 | INKING ROLLER HOLDER LEFT HAND |
| 411-21-02-115 | INKING ROLLER HOLDER RIGHT HAND |
| 411-21-02-116 | SPRING FOR HOLDER |
| 411-21-03-046 | RIGHT BLOCK, HOLDER FOR MODIFIED SP |
| 411-21-03-051 | LEVER RIGHT HAND CPL. (BATHING FNTN |
| 411-21-03-052 | LEVER LEFT HAND CPL. (BATHING FNTN. |
| 411-21-03-054 | SPRING |
| 411-21-03-055 | LEFT BLOCK, HOLDER FOR MODIFIED SPR |
| 411-21-03-066 | INK CONTAINER INCL. LOCKING PIVOT 4 |
| 411-21-04-005 | INKING ROLLER COMPLETE |
| 411-21-06-005 | NICKEL PLATED VENT TUBE |
| 411-30-07-008 | BEVELED WASHER FOR CLAMPING LEVER C |
| 411-30-07-009 | CLAMPING LEVER COMPLETE |
| 411-30-09-001 | BLOCK HOLDER SHEET - PRINT STA #1 |
| 411-30-09-002 | BLOCK HOLDER SHEET - PRINT STA #3 |
| 411-30-09-005 | BLOCK HOLDER SHEET - PRINT STA #2 |
| 411-30-09-006 | BLOCK HOLDER SHEET - PRINT STA #4 |
| 411-30-09-008 | BLOCK HOLDER SHEET FOR STA. 2, 3 & |
| 411-30-09-010 | BLOCK HOLDER SHEET SHORT/PRNT STA#1 |
| 413-00-00-017 | CLUTCH FOR VERTICAL BELT |
| 413-00-00-030 | SLIDING RAIL |
| 413-02-03-009 | BOTTLE CONVEYOR LOGIC |
| 413-08-01-017 | SPRING FOR POTENTIOMETER |
| 413-10-03-012B | BELT HOLDING AXLE |
| 413-10-17-101 | PRESSION BELT 17mm HT. 1000MM LONG |
| 413-10-20-203 | GUIDING PRESSION SLIDE FEEDING 20mm |
| 413-10-20-205 | SPONGE FOR PRESSION BELT 20mm HEIGH |
| 413-10-20-206 | GUIDING PRESSION SLIDE TAKE OFF 20m |
| 413-10-20-210 | GUIDING PRESSION SLIDE FEED 17MM HE |
| 413-10-20-212 | GUIDING PRESSION SLIDE TAKE OFF 17M |
| 413-10-20-300B | BACK OF BELT PRESSION SLIDE 20mm HE |
| 413-10-30-101 | PRESSION BELT 30mm Ht. (SEE NOTES) |
| 413-10-30-205 | SPONGE PRESSION BELT 30mm HEIGHT |
| 413-10-40-101 | PRESSION BELT 40mm HT. (SEE NOTES) |
| 413-10-40-203 | GUIDING PRESSION SLIDE FEEDING RIGH |
| 413-10-40-205 | SPONGE PRESSION BELT 40mm HEIGHT |
| 413-10-40-206 | GUIDING PRESSION SLIDE TAKE OFF LEF |
| 413-10-40-300B | BACK OF BELT PRESSION SLIDE 40mm HE |
| 413-14-00-012 | BELT GUIDING (VERTICAL BELT) |
| 413-14-20-011 | CONVEYOR BELT 20mm HT. (SEE NOTES) |
| 413-14-20-020B | BACK OF BELT CONVEYOR UNIT 20mm HEI |
| 413-14-30-011 | CONVEYOR BELT 30mm HT. (SEE NOTES) |
| 413-14-30-020B | BACK OF BELT CONVEYOR UNIT 30mm HEI |
| 413-14-40-011 | CONVEYOR BELT 40mm HT. (SEE NOTES) |
| 413-14-40-012 | GUIDING CONVEYOR UNIT LEFT HAND 40m |
| 413-14-40-020B | BACK OF BELT CONVEYOR UNIT 40mm HEI |
| 413-15-20-012 | GUIDING CONVEYOR UNIT RIGHT HAND 20 |
| 413-15-30-012 | GUIDING CONVEYOR UNIT RIGHT HAND 30 |
| 413-15-40-012 | GUIDING CONVEYOR UNIT RIGHT HAND 40 |
| 414-13-00-020 | FAN |
| 414-14-00-012 | PLATE LIST S1 24 (PLUG LEDGE) |
| 414-19-01-011 | ROLL (GUID. ROLLS TAPE UNWINDER) |
| 414-21-60-009B | POLYESTER SELF-ADHESIVE FOIL (ASSOR |
| 416-00-30-009B | CIRCUIT BOARD |
| 416-00-40-009 | PNP - NPN CONVERTER |
| 421-21-02-010 | SPROCKET ON FAR LEFT END OF PRINT S |
| BS-8RF | CLIP |
